AT&T PagePac Plus AmpliCenter Guide d'installation télécharger pdf (Page 49)

Input Priority Arrangement

NOTE: These priorities cannot

be rearranged.

Also, if you select more than one

zone to be inputs of the same

level (Input 1, for example), such

inputs will be handled on a first

in, first served basis. See Type

of Zone option, under General

Zone / Group Configurations

programming, later in this section.

The input priorities are pre-set at the factory. You may only assign a

priority level to inputs such as doorbell or security alarm, by assigning

them to Input #1 or Input #2, which differ in priority.

The default setting is:

1 – Attendant Access

2 – Input #1

3 – Telephone Access

4 – Input #2

5 – Night Bell

Music (always lowest priority)

2-20 Programming The Controller

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 91 92

AT&T 1
Trademarks 2
Warranty 2
Ordering Information 2
Support Telephone Numbers 2
Contents 3
About This Guide 5
How to Use This Guide 5
Getting Started 6
How to Comment on This Guide 6
Product Ordering Information 6
Reference Materials 6
Overview 7
■ LED Indicators 8
■ Back Panel Nomenclature 8
■ Connectors on Rear 8
About PagePac Plus 9
Security Protection 10
Overview 1-5 11
Managing the System 12
Installing System Hardware 12
Changing System Settings 12
Training Co-Workers 12
Solving Problems 12
Application Notes 13
Features and Capabilities 13
Daily Operation 13
Factory-Set Default Inputs 14
Eight Primary Paging Zones 15
48 Expansion Zones 15
Three Output Types 16
Talk-Back Amplifier 16
Tone Generator 16
Programming Memory 16
Hardware Configuration 16
Indicators and Connectors 17
LED Indicators 17
Back Panel Nomenclature 17
Amplicenter: 18
Controller Unit: 18
Zone Expansion Unit: 18
Overview 1-13 19
Connectors on Rear 20
Interface Considerations 21
Zone Map 22
Table 1-1. Zone Map Example 23
1-18 Overview 24
(Continuation Page 1) 25
1-20 Overview 26
(Continuation Page 3) 27
Zone Configuration Tables 28
Input Zones 29
Programming The Controller 30
Error Tones 31
Introduction 32
Programming by PC 32
At Power Up 33
Enter Programming Mode 34
Reset to Factory Defaults 35
Programming Steps 36
Connect Password 37
Programming Password 39
Forgot the Password? 40
Confirmation Tone ON/OFF 40
Pre-Announcement Tone ON/OFF 41
Talk-Back Warning Tone 42
VOX Disconnect Timing 43
Computer Monitor 44
Input Computer Monitor 45
COPY Command 46
Type of Zone: Input or Output 48
Input Priority Arrangement 49
Zone Monitor 50
Zone Grouping 51
Type of Output 52
Page Enable 54
Music Enable 55
7 ] [ 7 ] and 56
Night Bell Enable 57
Pass DTMF to the Output 58
Tone Selection 60
9 ] [ 3 ] and repeat 61
Tone Routing 62
Audio Source Enable 63
Audio Routing 64
To Enter the 66
Programming Mode 66
The Copy Command 69
Operation 70
Power UP 71
System Administrator 71
End User 71
Within 10 Seconds 72
After 10 Seconds 72
Unlock the Door 72
User Quick Reference Card 73
A-2 Application Notes 76
Background Music 77
A-4 Application Notes 78
Door Control 79
A-6 Application Notes 80
Alarm System Input 81
A-8 Application Notes 82
Talkback 83
A-10 Application Notes 84
Computer Monitor Paging Log 85
A-12 Application Notes 86
Amplifiers 87
A-14 Application Notes 88
IN-2 Index 90

Commentaires sur ces manuels

Pas de commentaire

AT&T PagePac Plus AmpliCenter Guide d'installation Page 49

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio AT&T PagePac Plus AmpliCenter